Hydrogen Sulfide Chemical Properties
- Melting point:
- −85 °C(lit.)
- Boiling point:
- −60 °C(lit.)
- dgas 1.19 (air = 1.00)
- vapor density
- 1.19 (15 °C, vs air)
- vapor pressure
- 252 psi ( 21 °C)
- 3779 | HYDROGEN SULFIDE
- Flash point:
- storage temp.
- colorless gas
- 7(at 25℃)
- Strong rotten egg odor detectable at 0.001 to 0.1 ppm (mean = 0.0094 ppm); olfactory fatigue occurs quickly at high concentrations
- Odor Threshold
- explosive limit
- Water Solubility
- 1g dissolves in H2O: 187mL (10°C), 242mL (20°C), 314 (30°C) [MER06]
- Stable. Highly flammable. May form explosive mixture with air. Note wide explosive limits. Incompatible with strong oxidizing agents, many metals. May react violently with metal oxides, copper, fluorine, sodium, ethanal.
- CAS DataBase Reference
- 7783-06-4(CAS DataBase Reference)
- EPA Substance Registry System
- Hydrogen sulfide (7783-06-4)
- Hazard Codes
- Risk Statements
- Safety Statements
- UN 1053 2.3
- WGK Germany
- Autoignition Temperature
- 260 °C
- DOT Classification
- 2.3, Hazard Zone B (Gas poisonous by inhalation)
- LC50 in mice, rats (ppm): 634, 712 (1 hr inhalation) (Vernot); LC50 in rats (ppm): 444 (4 hr inhalation) (Tansy)
Hydrogen Sulfide Usage And Synthesis
Hydrogen sulfide is used commercially to purifY hydrochloric and sulfuric acid, to precipitate sulfides of metals, and to manufacture elemental sulfur and organosulfur compounds. Chemical production processes using hydrogen sulfide include the manufacture of mercaptans; pharmaceuticals; plastics; adhesives; television, cathode ray tubes (CRT), and fluorescent tube phosphors; dyes; pigments; biodegradable pesticides; ethylene; nylon; soda ash; sodium hydrosulfide; heavy water; and others.
Hydrogen sulfide is used as a reducing agent in cresylic acid recovery. It is also used as a reagent in analytical chemistry. In waste water cleanup and groundwater restoration projects, hydrogen sulfide is used to immobilize heavy metals.
Hydrogen sulfide is generally found as a pungent colorless flammable gas, although it is commonly shipped as liquefied compressed gas (NIOSH, 2011). Its characteristic odor of “rotten eggs” cannot be considered indicative of its concentration, as olfactory fatigue occurs quite rapidly, even at relatively low concentration levels (100–150 ppm). It has a vapor density of 1.19, which makes it heavier than air and will cause it to accumulate in low lying areas rather than disperse easily in air and thus can present a hazard for workers in basements, subterranean locations, and confined spaces. It is soluble in water to a maximum of 0.4% by mass at room temperature. The auto ignition temperature is 260 °C and the flammable limits in air, % by volume are 4.5 (lower) and 45.5 (upper).
The tendency for belowground accumulation, coupled with its water solubility and flammability has proven to be a significant hazard for those who conduct work in underground tunnels or sewers (Adelson and Sunshine, 1966; Chen and Wang, 2012). Reactivity can occur from contact with strong oxidizers and oxidizing materials and result in fires and explosions. Hydrogen sulfide also attacks many metals resulting in the formation of sulfides and can lead to metal integrity issues.
Hydrogen sulfide (H2S) is one of the most important compounds of sulfur. It is a colorless gas with a foul, rotten-egg odor. It is well known in school laboratories when sulfur is being studied.
hydrogen sulfide (H2S) is known for its“rotten egg” odor and is a deadly poisonous gas even at 100 ppm of air. The laboratory reaction is FeS + 2HCl → H2S↑ + FeCl2.
Hydrogen Sulfide is a colorless, very poisonous, flammable gas with the
characteristic foul odor of rotten eggs. It often results
from the bacterial breakdown of organic matter in the
absence of oxygen, such as in swamps and sewers where
anaerobic digestion can take place. It also occurs in
volcanic gases, “natural gas”, and some well waters.
Hydrogen sulfide has numerous names, some of which
Small amounts of hydrogen sulfide occur in crude oil, but natural gas can contain up to 90%. About 10% of the total global emission of H2S is due to human activity.
Hydrogen sulfide is a colourless gas with strong odour of rotten eggs (odour threshold ca 0.2 ppt).
H2S is soluble in carbon disulfide, methanol, acetone and alkanolamines. A solution of hydrogen sulfide in water is initially clear but over time turns cloudy. This is due to the slow reaction of hydrogen sulfide with the oxygen dissolved in water, yielding elemental sulfur, which precipitates out.
Reported found in heated French beans, beef broth, vapors of canned beef, canned beef, beef extract, heated beef fat, raw beef, beer, bread, heated Brussels sprouts, cabbage, cooked celery, cheddar cheese, cooked and raw chicken, chives, heated coconut, codfish, ground and roast coffee, heated corn, heated egg, grapefruit juice, cooked herring, citrus juices, strawberry, cabbage, onion, potato, rutabaga, tomato, blue cheese, buttermilk, raw and boiled eggs, coffee, potato chips, rice, soybeans, okra, sweet corn, sake, squid, shrimps, cooked, fatty fish and other natural sources
Hydrogen sulfide is a colorless, flammable, toxic gas with the characteristic odor of rotten eggs.It is produced naturally from the anaerobic bacterial decomposition of organic wastes, occurs in volcanic gases and hot springs, is a product of animal digestion, and is generated in industrial processes. Hydrogen is a natural component of natural gas and petroleum; it is only a small fraction of oil (hundreds of ppm), but may form an appreciable component of natural gas. Natural gas typically contains up to 5% hydrogen sulfide. Natural gas is considered sour if the hydrogen sulfide content exceeds 5.7 mg of H2S per cubic meter of natural gas. The process for removing hydrogen sulfide from sour gas is referred to as sweetening the gas. Because hydrogen sulfide is associated with anaerobic respiration in sewers and swamps, it is referred to as sewer gas, swamp gas, or stink damp.
Hydrogen sulfide is used as an analyticalreagent and in the manufacture of heavywater. It occurs in natural gas and sewer gas.It is formed by the reaction of a metal sulfidewith dilute mineral acid, and in petroleumrefining.
To produce elemental sulfur and sulfuric acid; in manufacture of heavy water and other chemicals; in metallurgy; as analytical reagent.
Hydrogen sulfide has relatively few commercial uses. It is used to produce elementalsulfur, sulfuric acid, and heavy water for nuclear reactors.
By far the largest industrial route toH2S occurs in petroleum refineries. The “hydrodesulfurization” process liberates sulfur from petroleum by the action of hydrogen. The resulting H2S is converted to elemental sulfur by partial combustion via the Claus
Hydrogen sulfide is produced during anaerobic respiration (fermentation). Anaerobic respirationenables organisms, primarily bacteria and other microbes, to meet their energy needsusing sulfate, elemental sulfur, and sulfur compounds as electron acceptors instead of oxygen.
ChEBI: A sulfur hydride consisting of s single sulfur atom bonded to two hydrogen atoms. A highly poisonous, flammable gas with a characteristic odour of rotten eggs, it is often produced by bacterial decomposition of organic matter in the absence of oxygen.
Fluorine, chlorine, bromine, and iodine react with H2S to form the corresponding halogen acid. Metal sulfides are formed when H2S is passed into solutions of the heavy metals, such as Ag, Pb, Cu, and Mn. This reaction is responsible for the tarnishing of Ag and is the basis for the separation of these metals in classical wet qualitative analytical methods. Hydrogen sulfide reacts with many organic compounds.
Aroma threshold values
Detection: 10 ppb
Air & Water Reactions
Highly flammable; a flame can very easily flash back to the source of leak. Soluble in water to a maximum of 0.4% by mass at room temperature .
HYDROGEN SULFIDE reacts as an acid and as a reducing agent. Explodes on contact with oxygen difluoride, bromine pentafluoride, chlorine trifluoride, dichlorine oxide, silver fulminate. May ignite and explode when exposed to powdered copper in oxygen [Mertz, V. et al., Ber., 1880, 13, p. 722]. May react similarly with other powdered metals. Ignites on contact with metal oxides and peroxides (barium peroxide, chromium trioxide, copper oxide, lead dioxide, manganese dioxide, nickel oxide, silver oxide, silver dioxide, thallium trioxide, sodium peroxide, mercury oxide, calcium oxide) [Mellor, 1947, vol. 10, p. 129, 141]. Ignites with silver bromate, lead(II) hypochlorite, copper chromate, nitric acid, lead(IV) oxide and rust. May ignite if passed through rusty iron pipes [Mee, A. J., School Sci. Rev., 1940, 22(85), p. 95]. Reacts exothermically with bases. The heat of the reaction with soda lime, sodium hydroxide, potassium hydroxide, barium hydroxide may lead to ignition or explosion of the unreacted portion in the presence of air / oxygen [Mellor, 1947, vol. 10, p. 140].
Highly flammable, dangerous fire risk, explosive limits in air 4.3–46%. Toxic by inhalation, strong irritant to eyes and mucous membranes.
The acute toxicity of hydrogen sulfide by inhalation is moderate. A 5-min exposure to 800 ppm has resulted in death. Inhalation of 1000 to 2000 ppm may cause coma after a single breath. Exposure to lower concentrations may cause headache, dizziness, and upset stomach. Low concentrations of H2S (20 to 150 ppm) can cause eye irritation, which may be delayed in onset. Although the odor of hydrogen sulfide is detectable at very low concentrations, it rapidly causes olfactory fatigue at higher levels, and therefore is not considered to have adequate warning properties. Hydrogen sulfide has not been shown to be carcinogenic or to have reproductive or developmental effects in humans
Hydrogen sulfide is a highly toxic gas. Exposure to high concentrations can result inunconsciousness and respiratory paralysis.A 5-minute exposure to a concentration of1000 ppm can be lethal to humans. Prolonged exposure to concentrations between250 and 500 ppm can cause respiratory irri tation, congestion of the lung, and bronchialpneumonia. Toxic symptoms that have beennoted from occupational exposure to hydrogen sulfide in a heavy water plant areheadache, nausea, cough, nervousness, andinsomnia (ACGIH 1986). In addition, it isan irritant to the eyes. Conjunctivities mayresult from exposure to 20–30 ppm.
Compound is heavier than air and may travel a considerable distance to source of ignition and flash back. HYDROGEN SULFIDE forms explosive mixtures with air over a wide range. Also reacts explosively with bromine pentafluoride, chlorine trifluoride, nitrogen triiodide, nitrogen trichloride, oxygen difluoride, and phenyl diazonium chloride. When heated to decomposition, HYDROGEN SULFIDE emits highly toxic fumes of oxides of sulfur. Incompatible with many materials including strong oxidizers, metals, strong nitric acid, bromine pentafluoride, chlorine trifluoride, nitrogen triiodide, nitrogen trichloride, oxygen difluoride and phenyl diazonium chloride. Avoid physical damage to containers; sources of ignition; storage near nitric acid, strong oxidizing materials, and corrosive liquids or gases.
Flammability and Explosibility
Hydrogen sulfide is flammable in air in the range of 4.3 to 45.5% (NFPA rating = 4). Combustion products (sulfur oxides) are also toxic by inhalation. In the event of a hydrogen sulfide fire, stop the flow of gas if possible without risk of harmful exposure and let the fire burn itself out.
Hydrogen sulphide (H2S) is a colorless, poisonous, flammable gas with an odor of rotting eggs. It is found in cesspools and mines and is a by-product of decomposed substances containing sulphur. It is one of the gaseous end-products of the reduction of sulphate in highly degraded paddy fields. Hydrogen sulphide is also produced in the laboratory for use as an analytical reagent.
Dry hydrogen sulfide is satisfactorily handled under pressure at normal ambient temperatures in carbon steel or black iron piping. Carbon steels in wet applications are known to be subject to sulfide stress cracking and low- temperature brittle fracture under some conditions of temperature, stress, and pressure. While hydrogen sulfide itself is relatively noncorrosive to steel in many uses, factors such as impurities, pH, erosive conditions, and high thermal or mechanical stresses in the metal can cause severe corrosion problems. High-strength steels are subject to crack formation when exposed to hydrogen sulfide.
Hydrogen sulfide gas can be formed and released whenever waste containing sulfur is broken down by bacteria.
Hydrogen sulfide is a toxic, irritating, and asphyxiant
gas. The substance is known to be produced and metabolized naturally in the human
body at low concentrations, but can be
quickly fatal once the natural bodily defenses
ACGIH recommends a Threshold Limit Value-Time-Weighted Average (TLV-TWA) of 10 ppm (14 mg/m3 ) for hydrogen sulfide. The TLV- TWA is the time-weighted average concentration for a normal 8-hour workday and a 40-hour workweek, to which nearly all workers may be repeatedly exposed, day after day, without adverse effect.
ACGIH recommends a Threshold Limit Value-Short Term Exposure Limit (TLVSTEL) of 15 ppm (21 mg/m3 ) for hydrogen sulfide. The TLV-STEL is the IS-minute TWA exposure that should not be exceeded at any time during a workday even if the 8-hour TWA is within the TLV- TWA. Exposures above the TLV- TWA up to the STEL should not be longer than 15 minutes and should not occur more than 4 times per day. There should be at least 60 minutes between successive exposures in this range.
cylinders of hydrogen sulfide should be stored and used in a continuously ventilated gas cabinet or fume hood. Local fire codes should be reviewed for limitations on quantity and storage requirements.
Wash it, then pass the gas through a train of tubes containing saturated Ba(OH)2 (2x), water (2x), and dilute HCl [Goates et al. J Am Chem Soc 73 707 1951]. It is available in gas cylinders. HIGHLY POISONOUS.
Hydrogen sulfide is incompatible with strong oxidizers. It will attack many metals, forming sulfides. Liquid hydrogen sulfide will attack some forms of plastics, rubber, and coatings. H2S reacts violently with a variety of metal oxides, including the oxides of chromium, mercury, silver, lead, nickel, and iron.
To respond to a release, use appropriate protective equipment and clothing. Positive pressure air-supplied respiratory protection is required. Close cylinder valve and ventilate area. Remove cylinder to a fume hood or remote area if it cannot be shut off. Disposal Excess hydrogen sulfide should be returned to the manufacturer, according to your institution's waste disposal guidelines. For more information on disposal procedures, see Chapter 7 of this volume.
Hydrogen sulfide is available in a technical or commercial grade that is 99 mole percent minimum hydrogen sulfide. It is also available in higher purities, up to 99.99 mole percent minimum hydrogen sulfide.
Hydrogen Sulfide Preparation Products And Raw materials
- CHLOROCARBONYLSULFENYL CHLORIDE
- Triethylsilyl trifluoromethanesulfonate
- Tosylmethyl isocyanide
- PENTAFLUOROPHENYL SULFIDE
- 4-Fluorophenyl sulfone
- TrimethylSilyl Trifluoromethanesulfonate
- Ethyl trifluoromethanesulfonate
- S-ETHYL TRIFLUOROTHIOACETATE
- Trifluoromethanesulfonic anhydride
- Diethylaminosulfur trifluoride
- Trifluoromethanesulfonic acid tert-butyldimethylsilyl ester
- Methyl trifluoromethanesulfonate
- 2,2,2-TRIFLUOROETHYL P-TOLUENESULFONATE
- BIS(2,4,5-TRICHLOROPHENYL) DISULFIDE
- 4-CHLOROPHENYL SULFOXIDE
- 400-666-7788 010-82848833-
- +86 21 61551611
- 021-60549325 18616193163
- 18871490274 027-59599241-